Tapetech 03TT Mini Automatic Taper Instrukcja Użytkownika Pobierz pdf

Mini Automatic

aper

Operation and Maintenance Guide

“How

Professionals Finish

The

Job”

Revised

Mini automatic

taper

Operation

The mini

automatic

taper simultaneously

applies

tape

and

joint

compound

to any joint: walls,

corners,

and

ceil

ings. It

automatically dispenses

the

correct amount

joint compound

under

the

tape, regardless

of the

tool

user’s speed.

The mini

automatic

taper uses tape 2 1/16 to 2 1/8

inches (52-50mm)

wide.

Wider

tape will not fit and

narrower

tape

will

have a

tendency

to jam. Install the tape by

removing

the tape bail

(retaining

wire) and

placing

the roll of tape on

the

spindle

with the tape unwinding

clockwise

as you look at the roll. Feed the tape through

the tape guide with the

back

side

of the tape facing down

. When correctly installed,

the tape will curl over the drive wheel

Fill the mini

automatic

taper with joint

compound

using the

loading EasyClean® Pump

and the

gooseneck assembly.

sur

that the gate control

lever is in the

closed position. Place

the

automatic

taper on the

gooseneck

with the

filler

attachment

firmly

seated against

the nylon seal and move the

EasyClean® Pump handle

transfer

joint

compound

from

the pail to the mini

automatic

taper.

Keep

the mud pail full to

avoid

air being pumped

into the taper. To

avoid

overfill

ing,

place

your fingers in the

open

end of the tube while filling.

Stop pumping

when the

piston reaches

your fingers

(approximately 5

pumps

when empty

After loading

the mini

automatic

taper, stand

it on end and move the gate valve

control

lever to

engage

the drive mechanism

Now turn the key,

located

on the drive gear sprocket

until the joint

compound covers

the

leading edge

of the joint tape. This is

necessary

after each loading

The

automatic

taper should be held with one hand on the control tube and the other hand at the bottom of the mud

tube.

Start taping

with butt joints first and then sidewall

and ceiling

flat

joints.

For ceilings

use both

drive wheels

for

the

first 4 - 6

inches (100-150mm)

of tape to

secure

it to the

ceiling,

then tilt the

automatic

taper

toward

you at a

slight

angle leaving

only one drive wheel on the

drywall surface.

Walk backwards

, leading

with the

head

of the

tool.

To tape vertical

joints, place

the taper at the

bottom

of the joint, parallel

to and slightly

above

the floor.

Lead

with

the

head

of the

taper,

soon

possible

to make tracking

easier. Remember

to roll with only one wheel in

contact with

the wall until

about

inches

(75mm) from the top.

Stop completely,

cut the

tape,

pulling

the

control

tube toward

you, and roll to the end of the joint on

both wheels.

To start the next joint,

move

the drive

wheels

lightly

against the

surface

of the wall,

starting

the

compound

flow while

advancing

a new end of the tape with the

control tube.

To tape horizontal

joints, advance

the joint compound

and about

1 1/2

inches

(40mm) of tape by

pushing forward on

the

control

tube while rolling the drive wheels

on the wall.

Place

drive wheels

on the wall and roll

along

the joint.

Stop

about

2 1/2

inches

(60mm) from the end of the joint and cut the

tape.

Roll out the last 2 1/2

inches

(60mm) of

tape

while feeding

tape with the

control

tube. This will

apply compound

to the

beginning

of the tape for the next joint

To tape inside angle joints, both wheels must run in

contact

with the adjacent wall surfaces, bisecting

the angle with

the

automatic

taper. Tracking must be in a straight line with the creaser wheel

extended,

using the trigger

located

near

the

trailing end of the

automatic

taper. The

extended

creaser wheel secures the tape to the angle and eases the rolling

opera

tion. Avoid twisting the taper as you move along the angle to insure that you bisect the angle

correctly. Operating

the

taper

at a 45 degree angle to the joint, as soon as it is practical, will aid in the

prevention

of the tape “cr

eeping”.

1 2

Mini Automatic 1

Podsumowanie treści

Strona 1 - Mini Automatic

Strona 2

Komentarze do niniejszej Instrukcji

Brak uwag

Tapetech 03TT Mini Automatic Taper Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Narzędzia Tapetech 03TT Mini Automatic Taper. TapeTech 03TT Mini Automatic Taper User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Narzędzia Tapetech 03TT Mini Automatic Taper